* Read * |
Corbin's Dual Touring Saddle accepts two removable rider's backrests. Each backrest is fully adjustable for a tailored fit to your posture. In the front we have engineered the backrest to fold down to make it easier to mount the bike. This special hardware (internal to the saddle) also allows the backrest position fore and aft to be adjusted to your profile. Once the backrest is installed, both of these adjustments can be performed without removing the saddle from the motorcycle.
Naturally, you can use a single Corbin backrest that transfers front to back as needed or get two backrests for full time use. Installation of the backrest is easy enough to make this possible at a moments notice. Simply slide the backrest shaft into the built in hardware and secure it in place with the provided set screw. Adjust the backrest to the desired angle and you're back on the road in total comfort.
For the ultimate in luxury, we offer electric seat heaters in our Dual Touring saddle design. A single switch controls the heat for both the rider and passenger positions. The switch is conveniently located along the left side of the saddle so you can reach it without taking your hand off the throttle. The two position switch allows you to select a heat level depending on conditions. The level of heat is controlled automatically by a thermostat built into the control unit. This setup is very simple to install into your VTX wiring. Dual Touring seat is also available without heater units built in.
This saddle also accepts our chrome "V-rail" for an added nostalgic touch (but not if you are using the Honda sissy bar setup). Show quality chrome plating provides a nice touch of class. V-rail mounts directly to the Corbin saddle for simple installation. Naturally, we use genuine leather in all of our seat models to provide a luxurious ride that breathes with your body. A wide range of leather options are available for a custom look to suit your taste. We also include our tasteful "Tuck & Roll" stitch pattern and the option of chrome studs if desired (please specify). Leather will break in along with your foam shape to give you a personalized fit and will age gracefully with proper care. Take good care of your leather seat with a quality conditioner like Corbin's Saddle Cream.
If you already have your VTX setup for touring with the Honda sissy bar / luggage rack setup, our Dual Touring Saddle will work with it just fine. As mentioned before, our chrome v-rail will not work on the seat with this configuration. Sorry, but at this time we do not make a coordinating sissy bar pad for the Honda sissy bar. Our saddle was engineered to allow proper seat placement for your copilot while using the Honda rack or the adjustable Corbin backrest.
Speaking of Corbin backrests, our new Ovalbac series (model #02-S shown) is the hottest thing available for your VTX. Not only does the Oval shape make a great hand hold for your passenger, but they don't trap heat against your body like solid models do. Of course we sculpt them to provide contoured support for your back that doesn't create a pressure point on your spine. We've even made the backing plates removable to add a range of customizing options (see listings below). We even offer a painted model that coordinates to your factory paint scheme.
For Part Numbers, Pricing and Options, Please click on the ORDER tab.
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1. | |
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. We always design our basepans as flat as possible so bumps or odd shapes don't telegraph through the foam to your body. Click on the button at left to learn more... | |
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button. | |
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works. | |
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info | |
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away. | |
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info... | |
ELECTRIC HEAT: As an option we can include electric heat in this saddle! This option provides a true bit of luxury for when the temperature starts to drop. Simple to install with major components pre-built into the saddle. Just wire in the included pigtail and you're ready to roll. Click the button at left for complete info... | |
Warning! Heater elements should never be installed in motorcycle seats used by riders that cannot sense heat. | |
Measurements: |
Rider Seating: 16" wide x 13" long Passenger: 12" wide x 14" long Approx. seat height: 26" |
Installation Instructions: [Page 1] - [Page 2] | |
Installation: Dual Touring Saddle installs with a tongue in the front and a chrome tab in the rear that attaches to the stock stud with the original chrome acorn nut. Seat heaters come pre-installed in the saddle and our installation kit wires into your stock fusebox easily with all components included. | |
Adjusting the position of the rider's backrest is simple and can be accomplished without removing the saddle. Just fold down the rider's rest and install the appropriate set screw to set the fore & aft position of the backrest. | |
Heater switch is located along the left side of the saddle where you can eaily activate it while riding. Three position switch allows you to choose Off-Low-High as needed. | |
Corbin saddles (with very few exceptions) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you? | |
WARNING: Heater elements (when available) should never be installed in motorcycle seats that will be used by riders that cannot sense heat. This could create a hazardous condition. |
Saddle Cream Take good care of your new seat and it will take care of you! Perfect for all your leather goods. $25 Standard Ovalbac Our most popular backrest is the perfect blend of form and function. Nine inches of support. $345. *Learn More* Standard Backrest Similar to the Standard Ovalbac, but without the hole. Available Chrome studs too. $345. *Learn More* Ovalbac Edge Edge Ovalbac to compliment bikes with more angular lines. Eight inches of support. $345. *Learn More* Ovalbac Large Like the Standard Ovalbac with more support. 10" H x 12.5" W contact area. $345. *Learn More* Ovalbac Tee Extra large support cut away to provide clearance for passenger's legs. 13 inches tall. $345. *Learn More* Ovalbac Gunfighter The functionality of a backrest with the smallest appearance possible. Provides eight inches support. $345. *Learn More* Gunfighter Often used as a rider's backrest in Gunfighter seat models. Provides eight inches of vertical back support. $345. *Learn More* Corbin Glovebox Glove Box bolts up to your Standard model backrest (#297-SB & #02-SB) to provide four liters of locking storage. $518. *Learn More* Apparel We're often asked about tees and such so we caved in and had some Corbin gear made up. *Shop* Furniture Barstools & auto designs. Ready for a Corbin seat inside your house? A big hit for the man cave! *Explore* |
Testimonials: | |||||||
Comments? | Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM. | ||||||
Submit Photos: | Showcase your bike on Corbin.Com! Use this form to upload photos for possible inclusion on our website. Ready, set... LET'S SEE 'EM! | ||||||
General Contacts |
|
  | ITEM | DESCRIPTION | PRICE | |
#H-VTX13-DT-4-E | Dual Touring saddle, VTX 1300 w/ Heater | $998 | ||
#H-VTX13-DT-4 | Dual Touring saddle, VTX 1300 no heater | $773 | ||
#VR-DT | Chrome V-Rail | $282 | ||
#02-SB | Ovalbac Standard Backrest (each) | $345 | ||
COVER | Select Your Material Options Below | |||
Seating Material - Leather Recommended | ||||
Side Panels - Vinyl Recommended | ||||
Stud Band Material - Vinyl Recommended | ||||
Stud Options | ||||
Welt Material | ||||
Stitching Color | ||||
Stitch Color for Corbin Logo | ||||
Enter Special Instructions Below | ||||
Select the checkbox next to all parts you would like added to your cart. Please be sure to select your cover options, if applicable, before clicking the "Add To Cart" button. | ||||
If you are concerned about how a material is going to look, we will be happy to send samples at no charge. Just go HERE and use the Chatbot to order. |
NOTE: Corbin products are designed to fit very close for cleanest look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you. Corbin Accessories should never be used with missing or damaged hardware as this can create an unsafe situation for rider &/or passengers. |
MILITARY & FIRST RESPONDERS: As a small token of our appreciation for your service to our country, we proudly offer a 10% discount to active military, veterans and first responders. Thank you for what you do! Be sure to notify us when the order is placed, we cannot change orders already in process. Call us at 800-538-7035 so our Reps can apply your discount. |
CUSTOM COVERS: You are always welcome to choose from our wide variety of colors and material options for your saddle. We provide these options at no extra charge as long as we can use our existing cover patterns. Creating a new cover design requires specialized custom work and will result in additional charges. |
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters, Coolers and workmanship are warranted for one year. Product will only be authorized to be shipped back for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA). |
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number. A note about paint color matching, PLEASE READ |
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges. |
Hand Made with Pride in the USA since 1968 | |
©Corbin-Pacific Inc | Privacy Policy | 800-538-7035 | Follow Us: |