Designed specially for Softails with the standard width fender and 150 series tire on the back (specifically the Softail Deluxe and Heritage Classic). Insist on a geniune Corbin saddle to improve the comfort and looks of your new bike. Our Dual Touring saddle is just what you need to maximize the long range capabilities of your Softail with enhanced comfort for two. Our ergonomically shaped seating gives you massive support for the long haul. The only reason you'll find for stopping is the need for fuel.
Designed to work with the H-D Detachable sissy bar in the rear or with the optional Corbin backrest system (V-rail will not work with sissy bar installed. ) Corbin backrests are supported by internal hardware for a very clean look and simple, one-bolt installation. You can order a single backrest and transfer it front to back as needed or get two for full time use. Backrest angle adjusts to provide a personalized fit to rider posture in both positions. In the front position, our special hardware allows positioning of the backrest fore & aft for riders of different stature. This special hardware also features a fold down action to ease mounting the bike. With backrest installed, the rider bucket offers 19 inches of vertical support!
Notice how both seating platforms are sculpted to fit the shape of the human body. This is what we call "ergonomic" design and it is one of the critical features of the Corbin saddle. Wide, dished platforms create more square inches of body contact and longer lasting support without hot spots. Inside, our exclusive Comfort Cell foam provides a firm, resilient ride that lasts. Over time, Comfort Cell will adapt to your body and provide a personalized fit for even greater comfort.
As with most Corbin saddles, this model uses genuine leather seating panels for a ride that breathes with your body. Luxurious and durable, leather will provide comfort for many years and will break in along with the foam shape for a personalized fit to your posture. We recommend our standard natural grain leather with tuck and roll stitching as shown. Optional chrome studs provide a nice nostalgic touch and are included at no charge if desired (please specify). For a little extra add electric heat (see below) or a chrome V-Rail to add to the nostalgic appeal.
For those chilly morning rides we offer an option of heated rider seating. We incorporate a heater unit under the leather seating and a switch on the left side of the saddle (so you can turn it on without removing your hand from the throttle). Just flip the switch to the low or high position and the seat will warm up and maintain temperature automatically through an integrated controller. Corbin's heater comes completely pre installed in the saddle and you need only integrate the included pigtail to your fuse box.
Notice how the saddle is designed to fit perfectly to the tank, chassis and fender... Corbin's Wizards have mastered where the leather meets the metal. This kind of fit is available only in genuine Corbin saddles through our patented Integrated Molding system. This process allows us to engineer extremely tight tolerances and fit complex shapes like the beautiful, flowing HD fender.
Need more options? Our #02-S model backrests have removable finishing plates on the rear available in a range of styles. The standard plate is an ABS leather look, but we can also provide a variety of options, please see individual backrest pages for exact details. You will find Corbin backrest models listed in the Accessories tab.
Installation is simple with a tongue in the front and a single bolt into your fender at the rear. For a very clean installation that requires no tools, we offer a chromed billet thumbscrew (#ACST-20). Just slide the saddle into place nose-first and tie down the rear into the stock location in your fender. Our optional chrome V-Rail bolts up directly to mounts internal to the Corbin saddle for simple installation and a very clean look. If you opt for electric heat, the saddle will include a pigtail wire that integrates directly with your Harley fuse box (complete instructions included).
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. We always design our basepans as flat as possible so bumps or odd shapes don't telegraph through the foam to your body. Click on the button at left to learn more...
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info...
ELECTRIC HEAT: As an option we can include electric heat in this saddle! This option provides a true bit of luxury for when the temperature starts to drop. Simple to install with major components pre-built into the saddle. Just wire in the included pigtail and you're ready to roll. Click the button at left for complete info...
Warning! Heater elements should never be installed in motorcycle seats used by riders that cannot sense heat.
Rider Seating: 14" wide x 16" long Back support w/ backrest: 19" Back support w/o backrest: 8"
Passenger: 12" wide x 12" long Back support w/ backrest: 10"
Fits these Harley-Davidson models: 2008 Softail Deluxe & Heritage Classic
Installation: The Corbin Dual Touring Saddle installs on your bike like stock using a tongue in the front and a single screw into your fender at the rear. Chrome V-Rail bolts directly to the saddle and doesn't require any outside brackets for installation... very clean!
Seat heater assembly comes preinstalled on the saddle and ready to go. We supply the wiring pigtail and adapter to connect the seat directly into your stock Harley fusebox. This is a simple procedure that can be handled by virtually any home mechanic.
If the main fuse is in the way of installing the bracket, shift it over the battery. The basepan will have a small groove allowing space for the fuse. Shown in the image to the right, move the fuse from point "A" to point "B".
The 2011 model comes with a thicker leather tank panel which may cause the front tongue to have difficulty catching the chassis. This is easily fixed by adding a slight downward bend to the seat's front tongue. You can easily do this with an adjustable wrench and a little pressure.
NOTE: This saddle does not fit the 2014 CVO Deluxe.
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Makes seat installation and removal a tool-free snap! Machined billet thumbscrew is polished and chromed for a very clean look. Available in the following sizes:
SAE: 1/4" x 20 or 1/4" x 28 Metric: m5 x .8, m6 x 1.0 or m8 x 1.25 *More Info*
Corbin's Chrome V-Rail bolts up easily to your Dual Tour saddle with no additional brackets. Triple-plate chromed for a show quality finish, the V-Rail provides a nice nostalgic look for your bike. Does not work with Sissy Bars installed. *More Info*
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
All the functionality of an adjustable backrest, combined with the smallest profile possible. This model is often used as a rider's backrest in Gunfighter seat models just like the #02-G shown above. Includes genuine leather seating and color coordinating options just like our saddles *More Info*
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM.
2360 Technology Parkway Hollister, CA 95023 800-538-7035
1433 North US HWY 1 Ormond Beach, FL 32174 800-223-4332
Want to test drive our Visual Seat Configurator? It's in Beta Testing now... Just click HERE.
Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.
Dual Touring Saddle w/ Heater
Dual Touring Saddle no heater
Ovalbac Leather Backrest (ea)
If you prefer to choose a different backrest model than the #02-SB, just click on the Accessories Tab above. You will be shown all of the Corbin backrest models currently available.
All Corbin saddles (with very little exception) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
Warning! Heater elements (when available) should never be installed in motorcycle seats used by riders that cannot sense heat.
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.