Now available from Corbin's Workshop of Wizards is this outstanding Classic Solo Saddle & Passenger Pillion for the newest Dyna-Glides. This saddle was designed to provide maximum rider comfort combined with a classy, nostalgic look. It provides the use of our removable rider's backrest for 13 inches of vertical back support. Our sculpted seating gives maximized body contact and provides a bucket that gives plenty of lower back support. Our neutralized seat platform offers an easier reach to the ground and a more ergonomic position on the bike. We also offer a "Close" version for smaller riders that need an easier reach to the bars and the ground.
Corbin's removable rider backrest is simple to install and adjusts easily to your riding posture. Choose from a variety of backrest styles to suit your taste although we recommend the #02-S Ovalbac ® for a good combination of looks and support. A range of finishing plate options are available for the rear of the backrest to further customize the look.
For ultra-cool solo looks, you can run the Corbin Classic Solo Saddle by itself without a pillion seat. This allows you to show off that slick rear fender and still provides for use of the Corbin backrest if desired. We've incorporated a new saddle mounting system on the model that uses a key lock. This makes it extremely simple to install and remove the seat as desired. Since the Passenger seat bolts directly to the Corbin Solo, you can easily go from a solo look to dual with just one bolt and a key latch... Simple!
Corbin's passenger pillion seat keeps a sleek, vintage look with capabilities for passengers. We build this model low to look sly, but use our high density Comfort Cell® foam for a firm supportive ride. Our dished shaping in the pillion seat provides good contoured support and minimizes the tendency to slide in the saddle. This pillion works with your Harley-Davidson sissy bar / backrest if desired... we even offer a coordinated sissy bar pad to complete the look. Sorry, but the pillion seat does NOT install with the Close version of our solo saddle.
To further customize the look of your bike, we can provide a variety of back plate options on our Ovalbac ® series backrests. Our standard back plate has a leather look or you choose from any of the styles listed. We can even provide a backing plate that is prepainted gloss black for just a little extra or, of course, the slick new chromed steel model shown here.
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. We always design our basepans as flat as possible so bumps or odd shapes don't telegraph through the foam to your body. Click on the button at left to learn more...
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info...
KEY LOCK INSTALLATION: This saddle model uses a new mounting system designed by Corbin to allow installation and removable with a simple key lock. Once the included brackets are installed, the saddle can be removed easily by just inserting and turning the key. Need a demo? Just click the button.
Classic Solo seating: 12.5" wide x 16" long 50's Pillion: 8.5" wide x 10" long Approx. Seat height: 29"
[Page 1] Corbin's Classic Solo and pillion use a new key-lock system. When used with a passenger pillion seat, Solo and pillion bolt together and install as a single unit with a screw into your fender at the rear in addition to the key latch. For tool free installation, use one of our chromed billet thumbscrews (#ACST).
To enable the key lock system, install the included bracket onto your chassis as shown here. This will provide a latch pin on the bike for saddle to mount to.
If using the passenger seat, mount it to the Classic Solo and install both pieces together as a single unit. Slide the nose of the Classic Solo into place with the tongue into the chassis and lower the solo onto the latching pin installed previously. Now install the stock screw into your fender through the chrome tab of the passenger seat. For an even simpler installation, use one of our chromed billet thumbscrews in place of your stock screw.
Passenger Pillion seat does not work with "Close" solo saddle.
Corbin saddles (with very few exceptions) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
WARNING: Heater elements (when available) should never be installed in motorcycle seats that will be used by riders that cannot sense heat. This could create a hazardous condition.
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Makes seat installation and removal a tool-free snap! Machined billet thumbscrew is polished and chromed for a very clean look. Available in the following sizes:
SAE: 1/4" x 20 or 1/4" x 28 Metric: m5 x .8, m6 x 1.0 or m8 x 1.25 *More Info*
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
All the functionality of an adjustable backrest, combined with the smallest profile possible. This model is often used as a rider's backrest in Gunfighter seat models just like the #02-G shown above. Includes genuine leather seating and color coordinating options just like our saddles *More Info*
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*
Click the "Design It" button to explore. You will be taken to our visual design tool where you can experiment and share it with your friends, add it to your shopping cart or just play around for a bit.
Classic Solo saddle
Close Solo Saddle
Passenger Pillion, Dyna-Glide
Passenger Pillion, WIDE-Glide
Ovalbac Standard Backrest (each)
Select the checkbox next to all parts you would like added to your cart. Please be sure to select your cover options, if applicable, before clicking the "Add To Cart" button.
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.
Corbin Motorcycle Saddles & Accessories Have Been Made with Pride in the USA since 1968