Our Dual Touring Saddle provides you and your passenger with sculpted seating and long range comfort with the luxurious option of electric seating heaters. Our generously contoured platforms provide better weight distribution to eliminate pressure points and give excellent support. Designed to work on all Dyna Wide-Glides with dual Corbin backrests or with your Harley-Davidson Sissy Bar... We even have a coordinated sissy bar pad to complete the look!
For the ultimate in luxury, we have the option of built in electric seat heaters in our Dual Touring saddle. A single switch controls the heat for both the rider and passenger positions. The switch is conveniently located along the left side of the saddle so you can reach it without taking your hand off the throttle. The two position switch allows you to select a heat level depending on conditions. The level of heat is controlled automatically by a thermostat built into the control unit. This setup is very simple to install into your Harley wiring.
Corbin's Dual Touring saddle accepts two removable rider's backrests for maximum back support. Each backrest is fully adjustable for a tailored fit to the rider posture. You can use a single backrest and transfer it front to rear as needed or you can order two backrests for full time use in your saddle. We offer several styles of backrest to suit your taste, but recommend the Ovalbac model #02-S shown here. This models provides the perfect blend of form and function. You will also probably notice the cool chrome finishing plate on the rear of the Ovalbac backrest... this is a brand new option available for your Corbin backrest!
In the front position, we have built in special hardware that allows for the backrest position to be adjusted fore and aft to provide for riders of different stature. This special hardware is also designed to allow the backrest to fold down out of the way to make it easier to mount your bike. Spring loaded hardware pops the backrest back up into position when you're seated. A very clean totally internal system!
As mentioned before, the Corbin Dual Touring saddle will also work with the Harley-Davidson Sissy bar if you prefer. Dual Tour works with either the stock sissy bar pad or with our coordinated pad #224. This offers a totally integrated look and sculpted support for your passenger. Of course, it is built up with the same quality materials as the saddle for long range comfort and support. Installs easily and covered to match your Corbin seat.
Corbin's Dual Touring Saddle also accepts our chrome "V-rail" for an added nostalgic touch, but not if you are using a sissy bar. Show quality chrome plating provides a nice touch of class. V-rail mounts directly to the Corbin saddle for simple installation that does not require drilling or brackets. To simplify mounting the saddle on your bike and provide a nice clean look, we also offer a chromed, billet thumbscrew. Available in two sizes, our thumbscrew gives tool-free installation of your new saddle.
UNIQUE TECHNOLOGY:
The design and manufacture of Corbin products is so unique that
Mike Corbin himself holds more than 60 United States Patents!
From the process itself to new innovations like the Corbin
Glovebox, you can count on highly functional and unique products
that work. Corbin products are manufactured under one or more of
the following US Patents: 6,848,156 B2; 6,729,516 B2;
D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937;
5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
FIBERTECH™ BASEPAN:
A purpose-built hybrid material that provides a firm foundation
to support the carefully designed ergonomics of the Corbin
saddle. It provides a precision fit to every arc and contour of
the machine and rides on rubber bumpers to protect your paint.
We always design our basepans as flat as possible so bumps or
odd shapes don't telegraph through the foam to your body.
Click the button at left to learn
more...
COMFORT CELL® FOAM:
The heart of the Corbin saddle! Our exclusive, purpose-built
foam material, called Comfort Cell, was created to
provide a firm, resilient ride that doesn't break down. This
means it will support you for long days on the road. Over time,
Comfort Cell will break in to provide a personalized fit to your
posture and even greater comfort!
For the complete story, just click the
button.
ERGONOMIC SHAPING:
A major part of the design criteria of the Corbin saddle is its
ergonomic shape. This means the saddle's foam shape is designed
to emulate the curves of the human body. This provides more
square inches of body contact and helps eliminate hot spots.
This shaping also neutralizes the seating platform to help curb
sliding in the saddle, which reduces fatigue. In a nutshell:
more comfort for a longer ride!
Click the button at left for an animation that shows
how it works.
PATENTED MANUFACTURING TECHNOLOGY:
Always an innovator, Mike Corbin invented Integrated Molding
technology, which is now the process by which all Corbin
saddles are made. This process allows extremely tight
tolerances and creates a chemical bond between the foam and
base material.
To see what this is all about, click the button for
more information.
GENUINE LEATHER:
We use leather in all panels of the seat that contact your body.
This provides a luxurious ride that breathes with your body.
Leather will also break in along with the foam shape to support
a personalized fit. Available in a wide range of textures and
styles to suit your taste.
For more information about leather seating,
click away.
CORBIN BACKREST SYSTEM:
The first and most versatile removable backrest system available
for motorcycles! Corbin's backrests provide added vertical back
support and long-range comfort. Supported by internal hardware
for a very clean look, the backrests adjust to the rider's profile
for a tailored fit and install or remove easily as desired.
A very popular option! Click the button for
additional information...
ELECTRIC HEAT:
As an option, we can include electric heat in this saddle!
This option provides a true bit of luxury for when the
temperature starts to drop. Installation is simple, with the
major components pre-built into the saddle. Just wire in the
included pigtail and you're ready to roll.
Click the button at left for
complete information...
Warning!
Heater elements should never be installed in motorcycle seats
used by riders who cannot sense heat.
Explore colors, materials and design options in our interactive
visual design tool. Experiment, share your creation or add the
finished design to your shopping cart.
Concerned about how a material will look? We will gladly send
samples at no charge. Visit our
materials page
and use the chatbot to place your request. Limitations apply.
Saddle Cream
Take good care of your new seat and it will take care of you!
Perfect for all your leather goods.
$25
Thumbscrews
Makes seat installation and removal a tool-free snap!
Machined from one piece of stainless steel for a very clean look.
Available in many popular sizes.
*Shop*
Standard Ovalbac
Our most popular backrest is the perfect blend of form and function.
Nine inches of support.
$383.
*Learn More*
Standard Backrest
Similar to the Standard Ovalbac, but without the hole.
Available with chrome studs too.
$383.
*Learn More*
Ovalbac Edge
Edge Ovalbac designed to complement bikes with more angular lines.
Eight inches of support.
$383.
*Learn More*
Ovalbac Large
Like the Standard Ovalbac, but with more support.
10" H x 12.5" W contact area.
$383.
*Learn More*
Ovalbac Tee
Extra-large support cut away to provide clearance for the
passenger's legs. Thirteen inches tall.
$383.
*Learn More*
Ovalbac Gunfighter
The functionality of a backrest with the smallest appearance
possible. Provides eight inches of support.
$383.
*Learn More*
Gunfighter
Often used as a rider's backrest in Gunfighter seat models.
Provides eight inches of vertical back support.
$383.
*Learn More*
Corbin Glovebox
Glovebox bolts to your Standard model backrest
(#297-SB & #02-SB) to provide four liters of locking storage.
$518.
*Learn More*
Measurements:
Rider Seating: 13.5"wide x 17" long Passenger: 11"wide x 10" long Approx. seat height: 29"
Installation of the Corbin saddle is simple. Our electric heat system is built into the saddle and wires into your fuse box with included adapters. Saddle is installed with a tongue in the front and a single screw into your fender at the rear. For tool free installation, use our chromed billet thumbscrew. A nice finishing touch!
Rider's backrest position can be adjusted fore and aft to adjust to your stature. Simply fold the backrest down as shown and replace the security screw through the top flap with the appropriate size for the position desired. Complete instructions and screw kit is included.
Corbin saddles (with very few exceptions) include
Genuine Leather Seating
to provide a luxurious look and feel... don’t let anybody tell you
that vinyl is just as good! You wouldn’t buy vinyl boots, would you?
WARNING:
Heater elements (when available) should never be installed in
motorcycle seats that will be used by riders that cannot sense heat.
This could create a hazardous condition.
Testimonials:
My sister and I visited your plant on Thursday, and we had a wonderful time. We can see how much pride and satisfaction your employees take in their work and your company. My compliments to you and your entire team. -Jon F.
Comments?
Of course we want to hear from you! Have some suggestions for us
or maybe comments for other riders? Send them via
THIS FORM.
Submit Photos:
Showcase your bike on Corbin.com! Use this form to upload photos
for possible inclusion on our website. Ready, set...
LET'S SEE 'EM!
General Contacts
California Factory:
Corbin Saddles
2360 Technology Parkway
Hollister, CA 95023
800-538-7035
Florida Showroom:
Corbin Saddles
1433 North US Highway 1
Ormond Beach, FL 32174
800-223-4332
PLEASE NOTE:
Corbin products are designed to fit very close to your bike for a clean look.
Due to this, other accessories or options can inhibit proper fit. As an example:
Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc.
If you have accessories installed on your bike, please let us know so we can
verify the fit for you.
MILITARY & FIRST RESPONDERS: As a small token of our appreciation for your service to our country, we proudly offer a 10% discount to active military, veterans and first responders. Thank you for what you do! Be sure to notify us when the order is placed, we cannot change orders already in process. Call us at 800-538-7035 so our Reps can apply your discount.
CUSTOM COVERS: You are always welcome to choose from our wide variety of colors and material options for your saddle. We provide these options at no extra charge as long as we can use our existing cover patterns. Creating a new cover design requires specialized custom work and will result in additional charges.
SADDLE WARRANTY:
Basepan, foam and hardware of the Corbin saddle is warranted to the original
owner for life. Cover materials, Heaters and workmanship are warranted for
one year. Product will only be authorized to be shipped back for refining of
shape or to replace/rectify defective parts. In cases where the rework requires
a new cover, a recover charge will be applied. Cash or credit refunds are not
available. All goods being handled for customer service consideration must be
accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY:
Structural integrity of Corbin fiberglass components are warranted to the
original owner for life. Finish and paint are warranted against manufacturing
defect for one year. Damage to product and / or painted surfaces from outside
forces or misuse is specifically not covered under warranty. Cash or credit
refunds are not available. All goods being handled for customer service
consideration must be accompanied by a Corbin receipt and a Return Material
Authorization (RMA) number.
EXPORT SALES:
USA pricing shown. When products are shipped throughout the world, you will
see higher prices because of freight, customs, duty & applicable taxes.
Please consider these costs when purchasing Corbin products outside the USA.
If ordering direct from Corbin, we will compute freight charges and add them
to the order. BUYER will be responsible for customs, taxes, duty or other charges.