WALL saddle for 2025 - 2026 Buell Super Cruiser 360 View
* Click or Tap to Activate Item *
Skip the highway and take the long way home.
We call this incarnation of the classic Corbin fastback saddle "The Wall" because of the impressive vertical back support brought about by the raised tail section. Part of a series of seats with a taller and more vertical back area that hold the rider in position more aggressively. We've found this works extremely well for high horsepower Buell where a less reclined posture is desired.
Up front, the ergonomically designed platform increases the area of body contact to disperse rider weight evenly and eliminate hot spots. Dished in the center to eliminate pressure on the tail bone. At the nose of the saddle we sculpt it close to the frame for ground reach. This model sits deeper into the chassis lowering reach by an inch and placing the rider into the sweet spot on the bike.
As far as passengers are concerned, the tail of the Wall saddle is padded and upholstered to provide for short trips. Although this is built with the same quality foam material as the rider's area, the shaping is designed primarily for looks and rider back support. When taking a passenger make sure you tell them to hold on tight! If you're looking for more two-up comfort, you'll want our Widowmaker saddle (Available Soon).
As always, our exclusive Comfort Cell® foam provides resilient comfort and a trim seating profile. High density foam provides a long lasting ride and plenty of support. The entire saddle touches your Buell ONLY with rubber bumpers to protect your paint job. Provides a perfect fit and contours the crown and profile of the fender.
Includes genuine leather seating panels in your choice of colors and styles for a truly distinctive touch. Leather seating is best because it breathes with your body and will conform with the foam shape for a personalized fit after break in. Leather is also extremely durable for years of enjoyment. Shown above:
Black Natural Leather seating, Charcoal Alcantara trim, Matte Black stud band, Trexx Gear sides, Matte Black tail, Brushed Aluminum welt, Medium Grey Stitching & Assembly stitching, and Champagne Corbin logo.
NOTE: If you would like to diminish (hide) the appearance of the assembly stitching, choose "Coordinate" on checkout and we will use a thinner thread that coordinates with the material being sewn so it blends in.
Saddle installs on your bike using a tongue in the front and a single bolt into your fender at the rear. For a very clean and simple, tool free installation, use one of our machined stainless steel thumbscrews at the rear. Available in a variety of sizes to suit multiple needs. The seat install location on your Super Cruiser uses an m8 thread, so the appropriate thumbscrew is #ACST-8M.
The finest and most comfortable motorcycle saddles available. Manufactured with pride in the USA.
UNIQUE TECHNOLOGY:
The design and manufacture of Corbin products is so unique that
Mike Corbin himself holds more than 60 United States Patents!
From the process itself to new innovations like the Corbin
Glovebox, you can count on highly functional and unique products
that work. Corbin products are manufactured under one or more of
the following US Patents: 6,848,156 B2; 6,729,516 B2;
D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937;
5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
FIBERTECH™ BASEPAN:
A purpose-built hybrid material that provides a firm foundation
to support the carefully designed ergonomics of the Corbin
saddle. It provides a precision fit to every arc and contour of
the machine and rides on rubber bumpers to protect your paint.
We always design our basepans as flat as possible so bumps or
odd shapes don't telegraph through the foam to your body.
Click the button at left to learn
more...
COMFORT CELL® FOAM:
The heart of the Corbin saddle! Our exclusive, purpose-built
foam material, called Comfort Cell, was created to
provide a firm, resilient ride that doesn't break down. This
means it will support you for long days on the road. Over time,
Comfort Cell will break in to provide a personalized fit to your
posture and even greater comfort!
For the complete story, just click the
button.
ERGONOMIC SHAPING:
A major part of the design criteria of the Corbin saddle is its
ergonomic shape. This means the saddle's foam shape is designed
to emulate the curves of the human body. This provides more
square inches of body contact and helps eliminate hot spots.
This shaping also neutralizes the seating platform to help curb
sliding in the saddle, which reduces fatigue. In a nutshell:
more comfort for a longer ride!
Click the button at left for an animation that shows
how it works.
PATENTED MANUFACTURING TECHNOLOGY:
Always an innovator, Mike Corbin invented Integrated Molding
technology, which is now the process by which all Corbin
saddles are made. This process allows extremely tight
tolerances and creates a chemical bond between the foam and
base material.
To see what this is all about, click the button for
more information.
GENUINE LEATHER:
We use leather in all panels of the seat that contact your body.
This provides a luxurious ride that breathes with your body.
Leather will also break in along with the foam shape to support
a personalized fit. Available in a wide range of textures and
styles to suit your taste.
For more information about leather seating,
click away.
Concerned about how a material will look? We will gladly send
samples at no charge. Visit our
materials page
and use the chatbot to place your request. Limitations apply.
Saddle Cream
Take good care of your new seat and it will take care of you!
Perfect for all your leather goods.
$25
Measurements:
Wall saddle: Approx. 12" wide x 16" long x 5.5" deep
Installation:
Installs easily with a tongue in the front and a single bolt into your fender at the rear. For tool free installation, use one of our stainless steel thumbscrews.
Rider seating is one inch lower than the OEM unit and provides a narrower nose to allow better ground reach.
Corbin saddles (with very few exceptions) include
Genuine Leather Seating
to provide a luxurious look and feel... don’t let anybody tell you
that vinyl is just as good! You wouldn’t buy vinyl boots, would you?
WARNING:
Heater elements (when available) should never be installed in
motorcycle seats that will be used by riders that cannot sense heat.
This could create a hazardous condition.
Testimonials:
My experience with the Corbin process was all the neat stuff I'd been told and then some. I didn't get everyone's names who worked on my Kawasaki Z750S, but everyone involved did a spectacular job. I'm more than happy with the seat, the service and the people involved. -Brian W.
Comments?
Of course we want to hear from you! Have some suggestions for us
or maybe comments for other riders? Send them via
THIS FORM.
Submit Photos:
Showcase your bike on Corbin.com! Use this form to upload photos
for possible inclusion on our website. Ready, set...
LET'S SEE 'EM!
General Contacts
California Factory:
Corbin Saddles
2360 Technology Parkway
Hollister, CA 95023
800-538-7035
Florida Showroom:
Corbin Saddles
1433 North US Highway 1
Ormond Beach, FL 32174
800-223-4332
PLEASE NOTE:
Corbin products are designed to fit very close to your bike for a clean look.
Due to this, other accessories or options can inhibit proper fit. As an example:
Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc.
If you have accessories installed on your bike, please let us know so we can
verify the fit for you.
MILITARY & FIRST RESPONDERS: As a small token of our appreciation for your service to our country, we proudly offer a 10% discount to active military, veterans and first responders. Thank you for what you do! Be sure to notify us when the order is placed, we cannot change orders already in process. Call us at 800-538-7035 so our Reps can apply your discount.
CUSTOM COVERS: You are always welcome to choose from our wide variety of colors and material options for your saddle. We provide these options at no extra charge as long as we can use our existing cover patterns. Creating a new cover design requires specialized custom work and will result in additional charges.
SADDLE WARRANTY:
Basepan, foam and hardware of the Corbin saddle is warranted to the original
owner for life. Cover materials, Heaters and workmanship are warranted for
one year. Product will only be authorized to be shipped back for refining of
shape or to replace/rectify defective parts. In cases where the rework requires
a new cover, a recover charge will be applied. Cash or credit refunds are not
available. All goods being handled for customer service consideration must be
accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY:
Structural integrity of Corbin fiberglass components are warranted to the
original owner for life. Finish and paint are warranted against manufacturing
defect for one year. Damage to product and / or painted surfaces from outside
forces or misuse is specifically not covered under warranty. Cash or credit
refunds are not available. All goods being handled for customer service
consideration must be accompanied by a Corbin receipt and a Return Material
Authorization (RMA) number.
EXPORT SALES:
USA pricing shown. When products are shipped throughout the world, you will
see higher prices because of freight, customs, duty & applicable taxes.
Please consider these costs when purchasing Corbin products outside the USA.
If ordering direct from Corbin, we will compute freight charges and add them
to the order. BUYER will be responsible for customs, taxes, duty or other charges.
MILITARY & FIRST RESPONDERS: As a small token of our appreciation for your service to our country, we proudly offer a 10% discount to active military, veterans and first responders. Thank you for what you do! Be sure to notify us when the order is placed, we cannot change orders already in process. Call us at 800-538-7035 so our Reps can apply your discount.