Hollywood Solo saddle for 1998-2005 Road Glide, 1997-2005 Electra-Glide & 2006 CVO Electra-Glide
Click or Tap to Activate Item
Hollywood Solo saddle gives your bagger a slick, low profile look while providing you with reasonable, boulevard cruising comfort. Our Fibertech basepan provides a perfect, flowing fit along the tank, chassis and fender, but rides on rubber bumpers to protect your paint job. The Hollywood Solo is built up with high density Comfort Cell® foam to provide a firm resilient ride despite the incredibly low profile.
For the versatility to take passengers along for the ride, we now offer a slick Pillion seat to work with the Hollywood Solo. Built low and sly just like the front seat, our pillion pad offers passengers firm support for short to mid-range rides. For tool-free installation, use one of our chromed billet thumbscrews; simply slide the nose of the pillion seat under the Hollywood Solo's mounting bracket and secure to your fender with the thumbscrew or stock bolt.
Does the Corbin Hollywood Solo saddle work with the... ? YES! Naturally, you can run our solo by itself for an Ultra-clean look (no pun intended), but if you need the added storage of a trunk, you can run the H-D Tour Pac in either the front position or the rear position. This is a new option from Harley for `05 where the Trunk is mounted forward in place of a passenger seat. This works with either the standard Tour Pac or with the low-profile "pizza box" style. Our pillion will also work in conjunction with your Harley-Davidson "detachable" passenger sissy bar setup. Naturally we make a matching trunkrest pad &/or sissy bar pad to complete the look.
The Hollywood saddle mounts with a new key lock system designed by the Corbin wizards. We include special brackets that bolt up to your chassis and have a stainless steel latch pin on top. Once the brackets are in place, you install the Hollywood Solo easily with a supplied key. Just slide the rear of the seat in place with a tongue under the fender bracket and lower onto the included latch pin at the front. To remove the saddle just insert the key, turn to release the lock and saddle is ready to remove... quick and simple!
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. We always design our basepans as flat as possible so bumps or odd shapes don't telegraph through the foam to your body. Click on the button at left to learn more...
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
KEY LOCK INSTALLATION: This saddle model uses a new mounting system designed by Corbin to allow installation and removable with a simple key lock. Once the included brackets are installed, the saddle can be removed easily by just inserting and turning the key. Need a demo? Just click the button.
Rider Seating: 13" wide x 18" long Hollywood Pillion: 8" wide x 12" long
Installation Instructions: [ Page 1 ] [ Page 2 ] Hollywood solo installs on a new keylock system. All brackets and required hardware is included so it's ready to go right out of the box.
First install the Corbin rear fender bracket on your bike using the studs and nuts already in your fender. Please note, Corbin's saddle will not work with the passenger grab rail installed. Remove the stock nuts and place the included bracket and washers on the studs. Center bracket on the studs and secure with stock nuts. Tighten to 8 ft lbs.
Now install the front clamshell bracket on the bike as shown and secure with the included bolts and washers. Center the bracket in the slot and tighten bolts to 10 ft lbs. Stainless steel latch pin should already be installed on Corbin bracket... If not, tread in latch pin with split lock washer and tighten to 8 ft lbs.
Your seat will now install by sliding the tongue at the rear of the saddle under the fender bracket and lowering the nose of the saddle onto the latch pin. Push down on the nose of the seat until you hear TWO clicks from the latch. Remove the seat by inserting key in the lock and turning clockwise.
When using with the H-D trunk in the front position, be sure to install the trunk first THEN the saddle.
This saddle does NOT fit the FLHX model!
Corbin saddles (with very few exceptions) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
WARNING: Heater elements (when available) should never be installed in motorcycle seats that will be used by riders that cannot sense heat. This could create a hazardous condition.
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Makes seat installation and removal a tool-free snap! Machined billet thumbscrew is polished and chromed for a very clean look. Available in the following sizes:
SAE: 1/4" x 20 or 1/4" x 28 Metric: m5 x .8, m6 x 1.0 or m8 x 1.25 *More Info*
Want to test drive our Visual Seat Configurator? It's in Beta Testing now... Just click HERE.
Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.