We always brag about how our R&D department can design products that visually fit the lines of the bike. Take a look at this setup and you'll see why! Notice how well they were shaped to emulate the tank and fender for total integration. This makes it hard to tell where the Yamaha stops and the Corbin starts!
We've taken approximately 60 liters of storage and smoothed out the lines to visually blend the saddlebags into the Warrior fender. The esthetics camouflage the generous capacity of the bags and look clean. Typical of Corbin engineering, the interior wall of the bag molds close to the profile of the bike to fit closer to the centerline than any other saddlebag made. This provides better load bearing, better balance, less width and a much cleaner look.
Corbin saddlebags are tooled up specially for each bike model so they fit perfect. Both bags feature top loading so contents can't spill out when opened and they will self close in the wind if forgotten. Notice how the Corbin mounting system keeps the bags close to the bike. We mold them around the fender rails and in tight to the fender. This allows the bags to carry weight in close for a better center of gravity and when loaded properly the bike remains stable at all speeds. This design also keeps a narrower profile for less width to worry about when lane splitting.
Because of the placement and size of the stock exhaust system, our design team shaped these bags to work with aftermarket systems only. Bags will fit with virtually any pipe system that is lower than the passenger foot pegs. Fleetliner Bags fit perfect and install simply with all brackets included. In the front, our bags are shaped to allow room for passengers legs on the rear footpegs and includes a heel pad to protect the saddlebag finish.
Both bags come completely lined to protect your cargo and feature locking doors for security. The Fleetliner saddlebag set comes prepainted to coordinate with your stock paint job. Heel pad comes standard with Asphalt material that is extremely durable and looks appropriate.
Manufactured of our exclusive Fibertech™ material for durability and a clean finish. Specially formulated for Corbin, Fibertech™ gives us very tight tolerances with minimal shrinkage so each part comes out true to the original design.
We use a quality gel-coat for a nice finish that doesn't show material weave. Most Corbin components are available prepainted and ready for immediate installation.
Corbin Bags come fully lined with a nice, thick grey liner on the inside to protect your cargo. Sure seal weather stripping around the doors keeps out the elements. Locking doors keep contents secure.
Capacity: Approx 30 liters per side Door Opening: 7.5" x 14.5" Overall weight w/ brackets: 33 lbs Overall width installed: Approx 25"
With 60 liters total capacity, Corbin Fleetliner bags offer 45% more storage than the THREE piece Cruiselite(TM) system offered as a Yamaha accessory!
Fleetliner Bags fit perfect and install simply with all brackets included.
Corbin saddles (with very few exceptions) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
WARNING: Heater elements (when available) should never be installed in motorcycle seats that will be used by riders that cannot sense heat. This could create a hazardous condition.
We do not always have a color match for all brands and model. Please enter your bike year and paint color below and we will contact you if we do not currently have the color matched. A note about paint color matching: Please Read
Please be sure to select/enter all options, if applicable, before clicking the "Add To Cart" button.
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.
Corbin Motorcycle Saddles & Accessories Have Been Made with Pride in the USA since 1968