Canyon Dual Sport saddle for 2012-2015 Triumph Tiger Explorer
Click or Tap to Activate Item
Our Canyon Dual Sport saddle design for the Tiger Explorer converts your stock two-piece seat into a very comfortable single piece unit with provisions for two optional backrests. Designed to maximize the comfort and usability of your bike while providing clean, custom looks.
By converting to a one-piece basepan, we were able to better place the seating position in the sweetspot to accomodate taller riders AND give good ground reach (the Tiger is a tall bike so keep expectations within reason). As an example, one of our test subjects is about 6'6" and found the seating postion to be excellent even while the seat height of our saddle is just slightly lower than the stock seat in the LOW position. We know this sounds unbelievable, but it works!
Another benefit of the single basepan is that it provides the structural integrity to support internal backrest hardware in both the rider and passenger seating positions. Corbin backrests install and remove easily into this internal hardware to provide a clean installation with excellent added support. Corbin backrests are available in a range of models to suit your style and the amount of support desired (#02-SB Ovalbac shown).
Our Canyon Dual Sport saddle works with a single backrest transferred front to back as needed or you can use two backrests full time. Backrests angle adjust to rider posture without having to remove them from the seat. Rider's position also features a fore/aft adjustment and folds down to ease mounting the bike.
This seat provides platforms that offer an increased area of body contact to give excellent weight dispersion and eliminate hot spots. Neutralized to curb the tendency to slide in the saddle which will greatly reduce fatigue. The shaping of the Corbin saddle relieves centralized pressure and supports from the sides. We build the saddle up with high-density Comfort Cell foam for a firm, supportive ride that lasts. Comfort Cell will support you for years and will provide a personalized fit after break in.
Covered using genuine leather for a perch that breathes with your body. Our quality leather will break in along with your foam for a luxurious ride. Just make sure you care for your saddle with a quality conditioner like Corbin's Saddle Cream. On this model we've used natural grain black leather in the seating with Asphalt vinyl sides, ghost grey welts and grey stitching. A coordinating colored welt and our tasteful stitch pattern add a nice subtle touch.
For the ultimately luxurious ride we include seat heaters in both the rider and passenger seating areas. They wire simply into your fusebox and feature a single control for the front and rear heaters. Switch is located on the left side panel (so you can keep your hand on the throttle) and is illuminated to indicate status. Corbin's tasteful tuck & roll stitch pattern adds a nice touch of class and is required to provide for the seat heater elements.
As an extra added value, Corbin's Ovalbac backrest models have a custom finishing plate option included at no extra charge. We have a standard leather-look plate, a Carbon-Fiber look or primer if you'd like to have it custom painted. For a little extra we can provide the finishing plate prepainted gloss black. Please be sure to choose your finishing plate option when ordering.
If you're looking to add a little bit more storage to your Tiger, it doesn't get any more convenient than the Corbin Glovebox. Four liters of weather resistant, locking storage that bolts to the back of your Corbin backrest in place of a finishing plate. Fully lined and weather stripped to protect your cargo. For complete information check the Accessories tab or click HERE.
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. We always design our basepans as flat as possible so bumps or odd shapes don't telegraph through the foam to your body. Click on the button at left to learn more...
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info...
KEY LOCK INSTALLATION: This saddle model uses a new mounting system designed by Corbin to allow installation and removable with a simple key lock. Once the included brackets are installed, the saddle can be removed easily by just inserting and turning the key. Need a demo? Just click the button.
ELECTRIC HEAT: As an option we can include electric heat in this saddle! This option provides a true bit of luxury for when the temperature starts to drop. Simple to install with major components pre-built into the saddle. Just wire in the included pigtail and you're ready to roll. Click the button at left for complete info...
Warning! Heater elements should never be installed in motorcycle seats used by riders that cannot sense heat.
Rider seating: 14" wide x 14" long Rear area: 13" wide x 12" long Approx seat height: 33.5"
Corbin's single piece seat installs easily and integrates with the Triumph key lock system. Includes brackets pre-mounted on the seat.
The height of our Canyon Dual Sport saddle is most comparable to the stock seat in the low position, but due to its improved seating position it works just as well for taller riders!
Corbin saddles (with very few exceptions) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
WARNING: Heater elements (when available) should never be installed in motorcycle seats that will be used by riders that cannot sense heat. This could create a hazardous condition.
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
All the functionality of an adjustable backrest, combined with the smallest profile possible. This model is often used as a rider's backrest in Gunfighter seat models just like the #02-G shown above. Includes genuine leather seating and color coordinating options just like our saddles *More Info*
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*
Canyon Dual Sport saddle with HEAT, Triumph Tiger Explorer
Canyon Dual Sport saddle no heater, Triumph Tiger Explorer
Click the "Design It" button to explore. You will be taken to our visual design tool where you can experiment and share it with your friends, add it to your shopping cart or just play around for a bit.
Canyon Dual Sport saddle with HEAT, Triumph Tiger Explorer
Canyon Dual Sport saddle no heater, Triumph Tiger Explorer
Glovebox Only, Painted Black
Ovalbac Standard Backrest (each)
Select Cover Options Below & Add to Cart
Select the checkbox next to all parts you would like added to your cart. Please be sure to select your cover options, if applicable, before clicking the "Add To Cart" button.
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.
Corbin Motorcycle Saddles & Accessories Have Been Made with Pride in the USA since 1968