At one point we accidentally referred to this bike as the M109's Little Brother... sorry about that.
Sure, it's compressing 300cc's less fuel & air, but a term like that sounds too dismissive for a motorcycle as grand as this one. The unfortunate side of this comparison is that most people didn't really like the stock seat on the M109 either. For all of its technical prowess, the good folks at Suzuki left a bit to be desired when it comes to the rump rest. Fortunately, we knew just what to do about that!
We started by designing a two piece saddle that will interchange with the OEM front seat, rear seat and cowling. We developed concave seating surfaces that conform to the shape of your body and eliminate pressure points. This also spreads body weight over a greater area giving more square inches of body contact and support. Additionally, both positions are neutralized to curb sliding which reduces rider fatigue.
As you can tell, this ergonomically designed shape provides a very nice visual effect that flows with the bike's sleek lines. Our Fibertech base material allows us to provide a perfect fit to every arc and contour of the Boulevard bodywork while being rigid enough to support the carefully designed foam shape. Fibertech also provides the structural integrity needed for our internal backrest support system.
Corbin backrests (optional) are designed to install easily and lock in place with a single bolt. Built in angle adjustment allows our backrests to be tailored to your riding posture quickly and easily. Use a single backrest to transfer front to rear as needed, or order two backrests for full time use. Choose from a variety of backrest styles to suit your taste (we recommend Ovalback #02-SB as shown above).
Naturally, our backrests are tailored to match your new Corbin saddle and provide an integrated look. Models like the #02-SB (shown) provide contoured support and maximum amount of body support. These models also offer finishing plate options to further customize the look of your M90. Backrests come standard with a leather look ABS finishing plate that can be ordered custom in a variety of styles... even chrome.
For an added bit of luxury, we've designed the front and rear saddles with the option of electric heat! Simple to install with all components built into the saddles. You just have to install a simple wiring pigtail on your bike and enjoy the warmth. A great feature to have when you're taking off early in the morning to beat the traffic! Convenient switch is located on the left side of the saddle. Once on, the saddles warm up and maintain temperature automatically. Both front and rear seats are available heated (or non-heated) and have separate switches to control them.
Constructed with our exclusive high-density Comfort Cell foam that allows us to build a supportive saddle without a bulky shape. Corbin's Wizards are masters at combining form and function into a saddle that makes you as happy to look at as it does to ride on. On top, we include genuine leather seating in a variety of distinct styles. Shown here in the following material combination: Black Faux Ostrich seating, Plain Black trim, Asphalt sides, No welt. Stitching in trim panel comes standard.
Simple installation with all required brackets included. Rear saddle mounts just like stock reusing the two stock bolts into your chassis. Front saddle mounts using the Suzuki key lock system with brackets preinstalled on the saddle. All Corbin components will interchange and work with stock seats & seat cowl.
Want some locking storage? Corbin's glovebox is an excellent solution for all your quick-access stuff. Simply replace the finishing plate on the Ovalbac model backrest and you've just added four liters of locking storage capacity. It's plenty for a couple bottles of water, cell phone, spare gloves, maps and other incidentals. Constructed of durable ABS plastic and available plain black or prepainted (at additional cost). Check out the optional Glovebox via the Accessories tab.
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. We always design our basepans as flat as possible so bumps or odd shapes don't telegraph through the foam to your body. Click on the button at left to learn more...
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info...
ELECTRIC HEAT: As an option we can include electric heat in this saddle! This option provides a true bit of luxury for when the temperature starts to drop. Simple to install with major components pre-built into the saddle. Just wire in the included pigtail and you're ready to roll. Click the button at left for complete info...
Warning! Heater elements should never be installed in motorcycle seats used by riders that cannot sense heat.
Rider seating: 16" wide x 13" long Vertical support: 7" Vertical with #02-SB: 17" Passenger seating: 12" wide x 11" long Approx. seat height: 28"
Front saddle installs just like stock and integrates with your Suzuki key lock system.
Rear saddle installs like stock with a tongue in the front and reusing the two stock bolts at the front.
Corbin's front and rear saddles will also interchange with your stock front and rear seats.
Corbin saddles (with very few exceptions) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
WARNING: Heater elements (when available) should never be installed in motorcycle seats that will be used by riders that cannot sense heat. This could create a hazardous condition.
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
All the functionality of an adjustable backrest, combined with the smallest profile possible. This model is often used as a rider's backrest in Gunfighter seat models just like the #02-G shown above. Includes genuine leather seating and color coordinating options just like our saddles *More Info*
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*
Want to test drive our Visual Seat Configurator? It's in Beta Testing now... Just click HERE.
Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.
Front saddle w/ Heat, 2009+ Boulevard M90
Front saddle no Heat, 2009+ Boulevard M90
Rear saddle w/ Heat, 2009+ Boulevard M90
Rear saddle no Heat, 2009+ Boulevard M90
Glovebox, painted. Backrest sold separately.
Ovalbac Leather Backrest (ea)
If you prefer to choose a different backrest model than the #02-SB, just click on the Accessories Tab above. You will be shown all of the Corbin backrest models currently available.
Choose Your Custom Cover Options
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.