You want your Bagger to look low and phat, but you need a little more storage right? It's an all too common problem of course, but now we have an excellent solution for you and it's called The Smuggler.
This setup includes a comfortable, sporty looking front saddle combined with a smooth tail section that serves as convenient, locking storage. The two pieces bolt to each other and the assembly then mounts to your bike with a tongue in the front and a single screw into your fender in the stock location at the rear. Once installed, the Smuggler setup provides a very clean and flowing solo look to your bike.
Up front, the comfort is pure Corbin with our exclusive Comfort Cell® foam material and ergonomically designed seating. The rider's position is sculpted to fit the shape of the human body providing more square inches of body contact and helping to eliminate pressure points that cause hot spots. Inside, our foam material gives a firm, resilient ride that supports you indefinitely. Over time, the foam will actually break in and conform to your specific body shape for a personalized fit. Our foam material feels firm when you first ride it, but this firmness is what gives you the ability to ride great distances in comfort.
A coordinated bump pad mounts on the front of the Smuggler trunk to provide generous back support. Naturally, the pad is built up with the same quality materials as the front seat for good resilience and support. In the center of the pad you will also see the locking latch mechanism that opens the Smuggler door panel.
The trunk itself provides a generous 6.4 liters of storage. This is plenty of room for incidental items like sunglasses, water bottles, cell phones and the like. On the inside, Corbin's Smuggler trunk is fully lined to protect your cargo and help to give a cushioned ride. Fully weather stripped to keep contents dry while the locking latch assures it's all secure.
Smuggler is constructed of Fibertech material for durability and a perfect finish and comes to you prepainted to coordinate with factory paint. Trunk liner, locks and weather stripping is all included and comes preinstalled so the setup is ready to go right out of the box.
For those chilly morning rides we offer an option of heated rider seating. We incorporate a heater unit under the leather seating and a switch on the left side of the saddle so you can turn it on without removing your hand from the throttle. Just flip the switch to the low or high position and the seat will warm up and maintain temperature automatically through an integrated controller. Corbin's heater comes completely pre-installed in the saddle and you need only plug the included pigtail to your fuse box. Note: Smuggler bump pad is not heated on this model.
Our saddle features genuine leather seating for a perch that breathes with your body and breaks in with the foam shape. Choose from a variety of leather styles to customize the look of the saddle or go with standard natural grain leather for a subtle look. Leather makes an excellent cover that is extremely durable and luxurious to ride on. As your saddle ages, the leather will take on its own unique character just like your leather jacket does. Just be sure to care for your new saddle properly with a quality leather conditioner like our Saddle Cream.
For simple installation, the saddle / trunk combination installs as a single piece using a tongue in the front and a single bolt into your fender at the rear. If you choose the heated option, we also include the pigtail to wire the saddle directly into your stock fuse box. The heater unit and controller are pre-installed in the saddle.
Click on this thumbnail to view a description of how the cover pattern on this seat model is described. This will help in the ordering process to assure you get exactly what you want.
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. We always design our basepans as flat as possible so bumps or odd shapes don't telegraph through the foam to your body. Click on the button at left to learn more...
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
ELECTRIC HEAT: As an option we can include electric heat in this saddle! This option provides a true bit of luxury for when the temperature starts to drop. Simple to install with major components pre-built into the saddle. Just wire in the included pigtail and you're ready to roll. Click the button at left for complete info...
Warning! Heater elements should never be installed in motorcycle seats used by riders that cannot sense heat.
Rider Seating: 13" wide x 13" long Back support: 7" Passenger: N/A Smuggler Capacity: 6.4 Liters
Installation: Smuggler trunk comes preassembled to the front seat and installs as a single unit using a tongue in the front and a single bolt into your fender at the rear. Uses stock location in rear fender.
If you opt for electric heat in the seat, all components will come preinstalled in the saddle. You will only need to integrate the included pigtail with your HD fusebox for power. Complete instructions included.
Because the Smuggler negates the ability to carry a passenger, it has not been tested to work with any backrest / sissybar system or Tour Pak.
Front seat and Smuggler Trunk are sold ONLY as a set although you will be ordering TWO part numbers below. Choose either a heated or non-heated seat and the trunk will automatically be included in your order.
Corbin saddles will not work with engine heat shields that mount on top of the frame and under the nose of the seat.
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM.
Showcase your bike on Corbin.Com! Use this form to upload photos for possible inclusion on our website: LET'S SEE 'EM!
2360 Technology Parkway Hollister, CA 95023 800-538-7035
1433 North US HWY 1 Ormond Beach, FL 32174 800-223-4332
Want to test drive our Visual Seat Configurator? It's in Beta Testing now... Just click HERE.
Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.
Front saddle w/ Smuggler, Heated HD Touring models
Front saddle w/ Smuggler, non heated, HD Touring Models
Smuggler Trunk included with either of the above
We do not always have a color match for all brands and models, especially at the beginning of the year when the new models come out. Please enter your bike year and paint color below and we will contact you if we do not currently have the color matched. A note about paint color matching: Please Read
All Corbin saddles (with very little exception) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
Warning! Heater elements (when available) should never be installed in motorcycle seats used by riders that cannot sense heat.
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.