Finally an attractive luggage solution for BMW’s new cruiser! Corbin is extremely proud to offer this set of sculpted hard saddlebags designed specifically for the lines of the R1200 C. These bags offer all of the convenience and security of hard saddlebags with the visual benefit of being designed for a specific motorcycle’s styling and chassis design.
Corbin’s Beetle Bags are fairly simple to install and come with everything needed except the paintwork. Our special molding process enables them to fit extremely well along the side of the bike to keep a narrower profile. Inside, each bag has a plush liner to help protect your cargo during transit while the outside of the bag emulates the shape of the BMW tank. The doors seal with a heavy duty weather stripping and open forward (into the wind) so that in the event a rider should forget to close the bag, no items will be lost.
Corbin’s saddlebag set includes a replacement rear fender that matches the styling of the original BMW fender. Our fender is a must for saddlebag installation as it includes the mounting points for the Corbin saddlebags. This is an exceptionally clean mounting system because it doesn’t require any additional out-board brackets that would create a
cluttered look and push the bags out further from the bike, upsetting your center of gravity.
Manufactured of our exclusive Fibertech™ material for durability and a clean finish. Specially formulated for Corbin, Fibertech™ gives us very tight tolerances with minimal shrinkage so each part comes out true to the original design.
We use a quality gel-coat for a nice finish that doesn't show material weave. When ordering parts in "primer gel-coat" you can expect a part ready for your painter's preparation. Most Corbin components are also available prepainted and ready for immediate installation.
Corbin Beetle Bags comes fully lined with a nice, thick grey liner on the inside to protect your cargo. Sure seal weather stripping around the doors keeps out the elements. Locking doors keep contents secure.
Saddlebag dimensions: 14.5" wide x 29" long x 16.5" deep
Door Opening: 7.5" wide x 12" long
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Makes seat installation and removal a tool-free snap! Machined billet thumbscrew is polished and chromed for a very clean look. Available in the following sizes:
SAE: 1/4" x 20 or 1/4" x 28 Metric: m5 x .8, m6 x 1.0 or m8 x 1.25 *More Info*
Corbin's Chrome V-Rail bolts up easily to your Classic Solo saddle with no additional brackets so installation is very clean. Triple-plate chromed for a show quality finish, the V-Rail provides a nice nostalgic look for your bike and simple installation. *More Info*
Corbin's Chrome V-Rail bolts up easily to your Dual Tour saddle with no additional brackets. Triple-plate chromed for a show quality finish, the V-Rail provides a nice nostalgic look for your bike. Does not work with Sissy Bars installed. *More Info*
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
All the functionality of an adjustable backrest, combined with the smallest profile possible. This model is often used as a rider's backrest in Gunfighter seat models just like the #02-G shown above. Includes genuine leather seating and color coordinating options just like our saddles *More Info*
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*
Dual Touring Saddle
If your bike is setup with luggage you must be ready to tour. If so, you're going to need a nice seat to seriously rack up the mileage. Corbin makes a Dual Touring seat model for both the Standard R1200 C and the Montauk.
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM.
2360 Technology Parkway Hollister, CA 95023 800-538-7035
1433 North US HWY 1 Ormond Beach, FL 32174 800-223-4332
Want to test drive our Visual Seat Configurator? It's in Beta Testing now... Just click HERE.
Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.
R1200 Saddlebag set w/ fender, primer
R1200 Saddlebag set w/ fender, painted
We do not always have a color match for all brands and models, especially at the beginning of the year when the new models come out. Please enter your bike year and paint color below and we will contact you if we do not currently have the color matched. A note about paint color matching: Please Read
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.